8 (775) 007-08-74


System « Teploskat »

The anti-icing systems, which are relatively new in the arsenal designers and builders of buildings and structures, quickly gained recognition. The use of de-icing systems « Teploskat » allows you to eliminate any noticeable formation of ice dams in the downpipes, gutters, on the edge of the roof and in other places it most likely to appear


system « Teploskat »

  • Increases the life of the roof and gutters
  • It prevents the destruction of facades buildings
  • secure against falling icicles and ice blocks
  • Fits on any roof
  • It does not require the dismantling of the summer

The main element of the system « Teploskat » are self-regulating heating cables, which are placed in areas most problematic areas - the lower part of the roof, gutters, gutters and with low power consumption melts the ice, preventing the formation of ice dams


system « Teploskat » contains the following elements:

Heating cables

The system « Teploskat » the most modern, reliable and effective self-regulating cables. It is self-regulating cables do deicing system effective, because:

  • Self-regulating cables themselves are changing their heat depending on the ambient conditions and temperature.
  • Self-regulating cables provide better contact with the heated surface, such as drip
  • Self-regulating cables reliably. In case of contact with them, leaves or dirt, they do not overheat.
  • self-regulating cable can be cut any desired length.

Automatic Control System

Controls the operation of the system « Teploskat » small automatic weather station with their sensors precipitation, temperature, water availability of sensors, timers and general manager of the microprocessor. The processor determines the time and the temperature of the heating cable, considering all the design features of your roof and its condition, weather conditions and temperature.

power distribution system

The system « Teploskat » using modern, reliable and safe power distribution systems that meet all the requirements of the SAE. They include switch boxes, plastic or metal pipes and ducts for passage of electric and signal cables. All the elements are arranged so that they are unobtrusive and do not spoil the appearance of the building.


The system « Teploskat » using robust clamps made of galvanized steel, copper, brass, non-marking on the roof of any holes. Different in form, they are securely fastened cable, do not break and do not change their strength from the temperature difference.

In addition, the system « Teploskat » can be used:

  • elements are heated snow retention;
  • heated rainwater.

Full range of services

The company Teplolux-AES provides all customers with de-icing systems « Teploskat » full range of services:

  • consultation on the initial stage of design and preparation basic technical solutions
  • the implementation of the licensed design department of design and estimate documentation
  • Completion and delivery of the complete set of materials and equipment required for the system installation at the site
  • execution of erection or installation work at the site
  • perform commissioning works and commissioning of the system

Teplolux-performing nuclear power project from scratch turnkey ensures customer quality and speed of work, reliability and efficiency of the operation, the actual warranty and post-warranty service. Every customer is constantly personal manager, which provides maximum ease of use and awareness of all stages.

Model Heated area

Typical heated areas of the system are:

    1. Downpipes the entire length.
    2. gutters and trays.
    3. Gutters funnel and the area around them, about 1 m2.
    4. input nodes gutters in drainpipes.
    5. Roof valleys (the junction line of the roof planes), other contiguity to the roofing plane & mdash; roof windows, lights, Attica.
    6. water cannons and water-jet window parapets.
    7. eaves.
    8. Drip.
    9. The surfaces of flat roofs and concrete drain tray.
    10. Drainage and drainage trays in the ground under the gutters.

The figure shows an example of typical heated areas.
Typical heated roof area

The stages of design

Designing a cable system « Teploskat » consists of several stages:

      1. Getting the customer's drawings buildings and structures with the designation of the heated parts of the roof and gutters, with a specific purpose designed system of heating.
      2. Photography and measurement of individual fragments of the heated sections of the roof.
      3. The classification of these sites, followed by separation of characteristic zones, and dangerous (from the point of view of snow accumulation and ice formation) places.

        Hazardous locations are:

        • gutters.
        • Funnels and noted drainpipes.
        • gutters and trays, especially in areas adjoining to gutters funnels.
        • Roof valleys (the joints of planes of different parts of the roof), roof windows, lights. Water Gun.
        • eaves. Drip.
      4. Defines the height of the building length, height and width of the roof, roof pitch, length and diameter of the drain pipes, the length and size of bins, chutes.
      5. The technical project for the design, in which, based on existing experience and recommendations are determined heated roof area, set specific heating power for all system components; the number and type of thread heating cable, if necessary, refined algorithm of the system.
      6. Calculate the required amount of heating cable, heated hoppers and the total electrical power system.
      7. The possibility of disruption from the surface roof blocks of ice and icicles, slipping into snowdrifts, outlines solutions to prevent them, to the installation of snow retention, working in concert with de-icing system.
      8. determines the type, quantity and parameters of heating sections and preliminary schemes of their layouts. Clarifies the power parameters of the heating system as a whole. Selects the fixings of a standard set.